9 Simple Steps to Waterproofing Exterior Walls

“The foundation of your home is built up by your walls. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. It’s not enough to paint the wall. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will start to peel off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

Dust and dirt are carried by air and stick to the outer part of the wall. To ensure the efficiency of the whole process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned with a broom, brush, or scraper. You can finish it off with a power washer.

Step 3: Check out for the cracks and fill them up

Cracks and holes can be found over time on your walls. Follow up the cleaning process with a thorough look at the cracks and holes on your wall. You can fill them with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

It is possible to seal the cracks with a cement mixture. Make sure you remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

To make sure your wall is waterproof, you need to apply a cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal on the exterior walls. It should become dry after that.

Step 5: Pick the right water-proofer

There are many products in the market that are waterproof. You have to pick the right one for the wall. Pick the water-proofer if it is a concrete wall or silicate-based one.

You can choose between a silicate-based concrete sealer and a concrete waterproof coating. Pick a plaster waterproof Additive to add strength to your walls.

Step 6: Apply the water-proofer

Apply the water-proofer with a roller or brush on the walls. Give a thin coat first, if you want to apply more than one layer. Let the first coat dry before adding the second.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layers, you need to use a tar-based pitch. You should apply it on your wall.

After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your walls.

Step 8: Consider adding gravel

If you want to lay the drainage pipes below the footer, you need a proper base. The drainage pipes are going to be supported by a 34-inches gravel base. Gravel is long lasting and provides enhanced protection.

You need to place the drainage pipe-cover along with the gravel. Next to the footer, level the position of the gravel and then back-fill it. Make sure the pipe is covered for at least 3 inches.

Step 9: Add a fabric barrier

Wrap the pipe with a fabric barrier. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system running. Then build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia

Conclusion:

Good waterproof gives your home a new life and strength to deal with outside weather related issues. If you want good waterproof solutions for your walls, Magicrete can help you. At a very low and affordable price, Magicrete offers proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”

Leave a Reply

Your email address will not be published. Required fields are marked *